Hyundai Accent

Repair and car operation



Hyundai Accent
+ 1. Maintenance instruction
+ 2. Engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. Control, decrease in toxicity
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Transmission
+ 10. Axes and power shafts
+ 11. Suspension bracket
+ 12. Steering
+ 13. Brake system
- 14. Body
   14.1. Specifications
   14.2. Adjustment of hinges of a cowl
   14.3. Trunk lid
   14.4. Adjustment of a door of a luggage compartment
   14.5. Forward door
   14.6. Back door
   14.7. Moldings
   14.8. Roof hatch
   14.9. External rear-view mirror
   14.10. Central console
   14.11. Dashboard
   14.12. Ceiling furnish
   14.13. Back shelf
   14.14. Luggage carrier upholstery
   14.15. Internal upholstery of salon
   14.16. Windscreen
   14.17. Back glass
   14.18. Front bumper
   14.19. Rear bumper
   14.20. Back seat
   14.21. Forward seat
   14.22. Search and elimination of malfunctions
+ 15. Central air
+ 16. Electric equipment
+ 17. Appendix
+ 18. Electroschemes






14.16. Windscreen

1–rasporny plug of a windscreen;
2–windscreen molding;
3–internal rear-view mirror;
4–windscreen;
5–windscreen lining.

Removal

PERFORMANCE ORDER
1. Before removal of a windscreen remove the following elements:

- top upholstery of a forward rack;
- internal rear-view mirror;
- screen wiper levers;
- overlay of the top part of a cowl;
- windscreen molding.
2. The special tool 09861-31100 cut hermetic of fastening of a windscreen.
3. If glass is repeatedly established, leave a hermetic layer on glass and a body. Note the provision of glass on a car body.
4. The special tool 09861-31400 remove a windscreen from the car.

Installation

PERFORMANCE ORDER
1. The special tool or a knife cut off old hermetic till thickness of a layer of 2 mm on all perimeter of a frame and a windscreen.

Prevention

Be careful not to remove some hermetic more than it is necessary, and also not to damage a paint and varnish covering of the car.


2. Degrease the processed surface.
3. Put a windscreen to a window aperture and in four points on a body note glass installation sites.
4. Paste a rubber lining to an internal surface of a windscreen.

Height of a layer of hermetic:
Above: 13,5 mm
From sides: 13,5 mm
From below: 27 mm

5. Establish a windscreen.
6. Apply a thin film a glass first coat on outer side of a rubber lining of a windscreen.

Prevention

Do not concern a hermetic layer a hand.
In a place of a contact of hermetic it cannot provide with a hand reliable connection and in this place leaks after glass installation are possible.
Do not put on glass a first coat intended for a body.


7. Apply a thin film first coats on originally put hermetic acting on perimeter of glass. It is necessary to establish glass during 10 mines after first coat drawing.
8. Put glue in a syringe and put it on windscreen edge.

Prevention

Put glue during 5 mines after drawing of a glass first coat.


9. The special tool or suckers establish glass over a window aperture according to earlier put labels and press glass to a window aperture.
10. With Shpatel remove superfluous glue. Fill all sinks and emptiness on windscreen perimeter.
11. Directing a water stream on a windscreen, check tightness of its installation. Do not direct on fresh hermetic a water stream under big pressure.
12. In the presence of leaks dry up the damaged area and put hermetic.

Prevention

Do not maintain the car within 4 hours after glass installation.
After installation of a windscreen support it within the first hour.


13. Establish into place all earlier removed elements.

Prevention

Within 2-3 days after installation of a windscreen do not clap doors.
Avoid movement on rough roads where the body of the car is exposed to intensive twisting.