Hyundai Accent

Repair and car operation



Hyundai Accent
+ 1. Maintenance instruction
+ 2. Engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. Control, decrease in toxicity
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Transmission
+ 10. Axes and power shafts
+ 11. Suspension bracket
+ 12. Steering
+ 13. Brake system
+ 14. Body
- 15. Central air
   15.1. Specifications
   15.2. Instruction on coolant application
   15.3. Remarks at replacement of elements of central air of air
   15.4. Connection of elements of central air of air
   15.5. Check of elements of central air established on the car
   15.6. Installation of manometers for pressure measurement
   15.7. Pumping of atmospheric air from central air
   15.8. Charging of central air of air
   15.9. Check of level of a coolant
   15.10. Verification of operational characteristics
   15.11. Oil for greasing of the compressor of the conditioner
   15.12. Relay check
   15.13. Conditioner compressor
   15.14. Plug of coupling and pulley of the compressor of the conditioner
   15.15. Coil of initiation of coupling
   15.16. Compressor check on the car
   15.17. Sensor of threefold (double) pressure
   15.18. Fan and condenser
   15.19. Evaporator
   15.20. Check of the thermostatic sensor (termistor)
   15.21. Air filter of the evaporator
   15.22. Heating and ventilation block
   15.23. Heater block
   15.24. Fan
   15.25. Search and elimination of malfunctions
+ 16. Electric equipment
+ 17. Appendix
+ 18. Electroschemes






15. Central air

Put in action the car engine the compressor compresses a gaseous coolant to a high pressure, thus the coolant temperature considerably raises. Then the compressed and warm coolant moves in the condenser established on a radiator of system of cooling. The condenser cools a gaseous coolant which turns into liquid. The liquid coolant arrives in the receiver / dryer where from it water is endowed, then submits liquid to the evaporator located in the block of a heater in salon of the car. In the evaporator the liquid coolant evaporates, passing to a gaseous state, and reduces temperature of air arriving in salon. Further the gaseous coolant arrives to the compressor and the cycle repeats again.

The relay of the conditioner operates electric chains of the fan of the condenser and the conditioner compressor. The management of the relay is carried out by the control unit the engine. If cooling liquid exceeds some temperature, the control unit the engine switches off the relay therefore central air is switched off. At start-up of the engine or car acceleration the control unit the engine switches off the relay therefore central air during 5 pages is switched off.

The fan blows air via the evaporator core therefore the stream of the cooled air submitted to salon of the car increases. Frequency of rotation of the fan is defined by position of the switch of the fan and the block of resistors.

The compressor of the conditioner is primary element of central air of air. If the compressor of the conditioner fails, there is no compression and coolant moving on a contour of central air of air. The compressor of the conditioner is put in action by a belt from a pulley of a cranked shaft.

Coupling of the compressor of the conditioner turns on the compressor. Coupling has electromagnetic management.

The condenser is established before a radiator. The fan of the condenser increases an air stream via the condenser.

The block of the fan / evaporator contains the engine of the fan, the conditioner relay, the core of the evaporator and the broad valve.

The core of the evaporator carries out functions of cooling and an air osushka. When cooling air moisture from air is besieged on the evaporator and in salon of the car the cooled dry air arrives.

The broad valve allows a liquid coolant to extend under a high pressure, entering into the evaporator. The valve passes a certain quantity of a liquid coolant to exclude evaporator flooding.

The drained air can be reheated, passing through a heater radiator. The radiator of a heater heats up hot cooling liquid passing through it.

In the receiver / dryer the liquid coolant from the condenser where from it water is removed arrives and then the coolant arrives to the evaporator.

Central air is filled with coolant R–134a.