Hyundai Accent

Repair and car operation



Hyundai Accent
+ 1. Maintenance instruction
+ 2. Engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. Control, decrease in toxicity
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Transmission
- 10. Axes and power shafts
   10.1. Specifications
   10.2. Power shaft
   10.3. A power shaft with CV JOINTS ball and type Birfield
   10.4. A power shaft with Birfield CV JOINTS and tripoidny type
   10.5. Rotary fist and nave of a forward wheel
   10.6. Back axis
   10.7. Search and elimination of malfunctions
+ 11. Suspension bracket
+ 12. Steering
+ 13. Brake system
+ 14. Body
+ 15. Central air
+ 16. Electric equipment
+ 17. Appendix
+ 18. Electroschemes



http://www.goodshelp.com/category/pakistan/ the constitution of Pakistan.



10.5. Rotary fist and nave of a forward wheel

1–bearing;
2–nut, 73–90 N • m;
3–rack;
4–rotary fist;
5–tip of steering draft;
6–nut, 15–34 N • m;
7–nave of a forward wheel;
8–brake disk;
9–nut, 220–260 N • m;
10-brake board;
11-nut, 60–72 N • m;
12-bolt, 65–75 N • m;
13-lock spring ring.

Removal

PERFORMANCE ORDER
1. Lift the car and remove a forward wheel.
2. Turn out a nut of fastening of a power shaft.
3. Remove a support and a soft wire fix it on a forward rack.
4. Remove the sensor of frequency of rotation from a rotary fist.
5. Take шплинт and unscrew a nut of fastening of a pin of the spherical hinge of a tip of steering bent for to a rotary fist. A stripper 09568–34000 squeeze out a pin of the spherical hinge from a rotary fist.
6. Note situation and turn out bolts of fastening of the lower part of a rack of a forward suspension bracket to a rotary fist.
7. A kapron hammer beat out a power shaft from a nave of a forward wheel. If the power shaft densely sits in a nave of a forward wheel, spray propitochny aerosol solvent on area шлицов and then repeatedly screw a nut with a fillet so that it settled down flush with a shaft end face. Striking on a nut with a brass hammer, beat out a power shaft from a nave.
8. A stripper 09568–34000 disconnect the spherical hinge of the bottom lever from a rotary fist.
9. Remove a rotary fist together with a nave of a forward wheel.
10. Installation is carried out to sequences, return to removal.

Dismantling

PERFORMANCE ORDER
1. Remove a brake disk from a nave of a forward wheel.
2. Remove a lock spring ring.
3. Establish special tools, as is shown in drawing.
4. Turning the special tool, remove a nave of a forward wheel from a rotary fist.
5. Remove the special tool and a dustproof ring.
6. The special tool remove an internal ring of the bearing from a nave.
7. The special tool remove an external ring of the bearing from a rotary fist.

Check

PERFORMANCE ORDER
1. Check a nave on lack of cracks and wear.
2. Check a brake disk on absence of development and damages.
3. Check the hinge on lack of cracks.
4. Check a spring ring on lack of cracks or damages.

Assembly

PERFORMANCE ORDER
1. Apply a thin film konsistentny greasing in an opening of a rotary fist and on an external ring of the bearing.
2. A press with an opravka of the corresponding diameter press the new bearing of a wheel.

Prevention

Do not make effort of a press an internal ring of the bearing.


3. Establish a dustproof ring.
4. A press with an opravka of the corresponding diameter press a nave in the wheel bearing.

Prevention

Do not make effort of a press an external ring of the bearing.


5. Establish a brake disk.
6. The special tool tighten a nave to a rotary fist, having tightened an adaptation bolt the moment of 240 N • m.
7. Several times turn a nave that elements of the bearing were established on the places.
8. Measure a torque which is necessary for putting for a bearing provorachivaniye.

Torque: 1,3 N • m

9. If a torque of 0 N • m, measure axial люфт the nave bearing.
10. If the torque exceeds demanded value, means, the bearing is incorrectly established in a rotary fist and on a nave. Disassemble a rotary fist and repeatedly bring together him.

Axial люфт bearing: 0,08 mm

11. Remove the special tool.