Hyundai Accent

Repair and car operation



Hyundai Accent
+ 1. Maintenance instruction
+ 2. Engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. Control, decrease in toxicity
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Transmission
+ 10. Axes and power shafts
- 11. Suspension bracket
   11.1. Specifications
   11.2. Bottom lever of a forward suspension bracket
   11.3. Replacement of the plug of the bottom lever
   11.4. Replacement of the plug (G) of the bottom lever
   11.5. Forward stabilizer of cross-section stability
   11.6. Rack of a back suspension bracket
   11.7. Replacement of the plug of the back longitudinal lever of a back suspension bracket
   11.8. Replacement of the plug of the back cross-section lever (And and In) a back suspension bracket
   11.9. Back stabilizer of cross-section stability
   11.10. Corners of installation of forward wheels
   11.11. Adjustment of a convergence of back wheels
   11.12. Wear of tires
   11.13. Antisliding chains
   11.14. Wheel palpation
   11.15. Tightening of nuts of fastening of a wheel
   11.16. Shift of wheels
   11.17. Check of withdrawal and course instability of the car
   11.18. Care of disks from an aluminum alloy
   11.19. Search and elimination of malfunctions
   11.20. Diagnostics of wear of tires
+ 12. Steering
+ 13. Brake system
+ 14. Body
+ 15. Central air
+ 16. Electric equipment
+ 17. Appendix
+ 18. Electroschemes






11.10. Corners of installation of forward wheels

Check of corners of installation of forward wheels is necessary for carrying out at the special stand, thus the car should be in horizontal situation with the forward wheels established for rectilinear movement. Previously be convinced that the forward suspension bracket and a steering are in a normal state, tires and wheels have no defects.

Convergence

The convergence is defined as a difference of distances (V-and) between lobbies and back boards of rims of wheels. The positive convergence means that wheels are in front located more closely to each other, than behind, at measurement at height of an average point of a wheel. If the convergence does not correspond to demanded value, weaken the left and right lock-nuts of tips of steering drafts, then, rotating drafts, establish demanded corners. Tighten lock-nuts. Turn on S of a turn of connecting drafts changes a positive convergence approximately to 5,5 mm.

Convergence: 0±3 mm

Prevention

Adjustment of a convergence should be carried out by rotation of the left and right tip of steering draft on an identical corner.
At adjustment of a convergence weaken an external collar of fastening of a protective cover to prevent its twisting.
After adjustment tighten lock-nuts of tips of steering drafts and collars of fastening of covers.


Moment of an inhaling of lock-nuts: 50–55 N • m

Disorder

Disorder is a tilt angle of a wheel in relation to a paving in the vertical plane. It can be positive if wheels are inclined outside, or negative if wheels are inclined inside. The disorder corner, generally influences cross-section forces.

Disorder: 0 °± 30'

Corner of a longitudinal inclination шкворня

The corner of a longitudinal inclination шкворня is established when manufacturing the car and cannot be regulated. If the corner of a longitudinal inclination шкворня does not correspond to demanded values, replace the pognuty or damaged details.

Corner of a longitudinal inclination шкворня: 1°48 '±30'

Prevention

Before check and adjustment of corners of installation of wheels the forward suspension bracket should be free from the worn-out, free or damaged details.
Adjustment of corners of installation of wheels is necessary for carrying out, using the special tool 09529-21000.
Disorder and corner of a longitudinal inclination шкворня are established when manufacturing the car and cannot be regulated.
If disorder and a corner of a longitudinal inclination шкворня do not correspond to demanded values, replace the pognuty or damaged details.