Hyundai Accent
+ 1. Maintenance instruction
- 2. Engine
- 2.1. SOHC engines
2.1.1. Specifications
2.1.2. Gear belt
2.1.3. Check of a tension of a gear belt
2.1.4. Adjustment of a tension of a gear belt
2.1.5. Poliklinova belt
2.1.6. Engine support
2.1.7. Forward cover and oil pump
2.1.8. Air filter (ACL)
2.1.9. Head of cylinders
2.1.10. Yokes
2.1.11. Hydraulic jacks of gaps of valves
2.1.12. Replacement of a saddle of the valve
2.1.13. Replacement of the directing plug of the valve
2.1.14. Valve
2.1.15. Camshaft
2.1.16. Rods
2.1.17. Cranked shaft
2.1.18. Flywheel
2.1.19. Piston finger
2.1.20. Final collector
2.1.21. Inlet collector and air chamber
2.1.22. Block of cylinders
2.1.23. Removal and engine and transmission installation
2.1.24. System of production of the fulfilled gases
2.1.25. Search and elimination of malfunctions
+ 2.2. DOHC engines
+ 3. Greasing system
+ 4. Cooling system
+ 5. Control, decrease in toxicity
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Transmission
+ 10. Axes and power shafts
+ 11. Suspension bracket
+ 12. Steering
+ 13. Brake system
+ 14. Body
+ 15. Central air
+ 16. Electric equipment
+ 17. Appendix
+ 18. Electroschemes
|
1–final valve;
2–saddle of the final valve;
3–the directing plug of the valve;
4–plate of a spring of the valve;
5–maslootrazhatelny cap;
6–valve spring;
7–holder of a spring of the valve;
8–crackers; |
9–crackers;
10-holder of a spring of the valve;
11-valve spring;
12-maslootrazhatelny cap;
13-plate of a spring of the valve;
14-the directing plug of the valve;
15-saddle of the inlet valve;
16-inlet valve. |
Removal
| PERFORMANCE ORDER |
|
1. The special adaptation compress a spring of the valve and remove from a valve core crackers. Slowly release the adaptation compressing a spring, and remove a valve spring, a plate of a spring and the valve from a head of the block of cylinders. |
Prevention
For storage of valves prepare the numbered plastic bags or containers.
|
| 2. Passatizhami remove a maslootrazhatelny cap. |
Prevention
Do not use repeatedly maslootrazhatelny cap.
|
|
Check
Valve spring
| PERFORMANCE ORDER |
| 1. Examine each spring of the valve on lack of cracks and damages. |
| 2. Measure length of a spring in a free condition. Establish a spring on a flat horizontal surface and measure a deviation of the top part of a spring from the vertical plane. Length of a spring in a free condition: 42,03 mm
Length of a spring under loading of 24,7 kg: 34,5 mm
Maximum permissible deviation of a spring from the vertical plane – no more than 1,5 °
|
|
Directing plugs of the valve
|
|
Check a gap between a core and directing the valve. If the gap exceeds maximum permissible value, replace directing plug of the valve with the plug of the increased repair size. Gap between a core and the directing plug of the valve:
Inlet valve: 0,03–0,06 mm
Final valve: 0,035–0,065 mm
Maximum permissible gap between a core and the directing plug of the valve:
Inlet valve: 0,1 mm
Final valve: 0,15 mm
|
The increased sizes of the directing plug of the valve
|
Increase in the size, mm
|
Dimensional label
|
Diameter of an opening in a head of cylinders, mm
|
|
0,05
|
5
|
11,05–11,058
|
|
0,25
|
25
|
11,25–11,258
|
|
0,35
|
50
|
11,50–11,508
|
Valve saddle
Check a condition and width of a working edge of a saddle of the valve. If necessary repair or replace a valve saddle.
Before replacement or repair of a saddle of the valve check wear of the directing plug of the valve. If the directing plug of the valve is worn-out, replace it.
|
|
Repair of a saddle of the valve is necessary for carrying out a nazhdachny circle or a mill. The width of a working facet of a saddle of the valve should be within technical requirements.
|
Valve
| PERFORMANCE ORDER |
1. Examine each valve on detection of the following defects:
– damages or deformation of a core of the valve;
– damages of a plate of the valve;
– damages or non-uniform wear of an end face of a core of the valve. |
|
|
2. If necessary, repair or replace the valve.
Thickness of an edge:
Inlet valve: 1,1 mm
Final valve: 1,4 mm
Maximum permissible thickness of an edge:
Inlet valve: 0,8 mm
Final valve: 1,1 mm
|
|
Installation
Prevention
Before installation clear all details.
Apply a thin film engine oil on all surfaces of sliding.
| PERFORMANCE ORDER |
|
1. Using the special adaptation 09222-22001, establish a maslootrazhatelny cap. |
| 2. Grease a valve core with engine oil and establish the valve. At installation of the valve do not apply big efforts not to damage a maslootrazhatelny cap. |
|
3. Establish springs and holders of springs. It is necessary to establish springs the party enamelled, to holders of springs. |
|
4. The special adaptation compress a spring. Establish crackers and remove the special adaptation for spring compression. |
| 5. Establish a head of cylinders. |
|
|
|