Hyundai Accent

Repair and car operation

12.17. Pump of the amplifier of a steering

1–bolt, 55–60 N • m;
2–sealing ring of round section;
3–bolt, 16 N • m;
4–a soaking-up pipe;
5–sensor of pressure of liquid;
6–pulley;
7–lock ring;
8–rasporny plug;
9–a shaft with the bearing;
10-sealing ring;
11-;;;;;;;

12-spring;
13-internal sealing ring;
14-external sealing ring;
15-forward lateral plate;
16-blades;
17-rotor;
18-pin;
19-statorny ring;
20-laying;
21-back cover;
22-bolt, 38 N • m.

Removal

Prevention

At service of the oil pump close the generator a polyethylene film.

PERFORMANCE ORDER

1. Disconnect a pressure head hose from the pump.
	2. Disconnect soaking-up filter from the socket of absorption and merge liquid in the container.
3. Weaken bolts of fastening of the pump and remove a driving belt.
4. Turn out assembly bolts of fastening of an arm of the pump and disconnect the socket of the sensor of pressure.
5. Remove the pump.

Dismantling

PERFORMANCE ORDER

	1. Remove soaking-up pipe and a sealing ring from the pump.
2. Remove a back cover with laying and pins.
3. Remove a statorny ring.
4. Remove a rotor and blades.
	5. Remove a forward lateral plate.
6. Remove internal and external sealing rings.
7. Remove a spring.
	Prevention At assembly it is necessary to use new laying and a sealing ring.
8. Unscrew a nut of fastening of a pulley and remove a spring washer.
	9. Remove a pulley and a segment shponka.
10. Using special flat-nose pliers, remove a lock ring.
	11. Squeeze out a pulley shaft with the bearing. If necessary use a kapron hammer.
12. Remove a sealing ring from the pump case.
	Prevention At assembly it is necessary to use a new sealing ring.
13. Remove an arm directing and unscrew nuts.
14. Disconnect the socket from the case of the pump and remove a throttle and a spring.
15. Remove a sealing ring from the socket.
	Prevention Do not make throttle dismantling.

Check

PERFORMANCE ORDER

1. Clear all details of the pump the corresponding solvent.

2. If there are damaged details of the pump, replace the pump assembled.

3. If the pulley is damaged or deformed, replace it.

4. If there are leakages of liquid about a sealing ring, replace it.

5. If shlitsa of a shaft or a pulley are damaged or worn-out, replace the corresponding details.

Assembly

PERFORMANCE ORDER

1. Establish the pump switch.
2. Establish a throttle spring, the valve and the socket in the pump case.
Prevention Grease with a thin layer of ATF DEXRON II liquid all replaced details, including oil consolidation and a sealing ring.
3. Establish an arm directing and screw nuts.
	4. The special tool 09222-32100 establish oil consolidation in the pump case.
5. Softly insert assembly of a shaft and establish a lock ring.
	6. Establish a pump pulley with a segment shponka.
7. Establish a spring both internal and external sealing rings.
	8. Establish a forward lateral plate.
	9. Insert pins into deepenings of the forward case, then establish a statorny ring, paying attention to the direction of its installation.
10. Establish a rotor so that labels on a rotor settled down from outside, an opposite forward part of the case.
	11. Establish blades the rounded-off parts outside.
12. Establish laying and a back cover.
13. Tighten the absorption socket.

Installation

PERFORMANCE ORDER

1. Establish the pump to a pump arm.

2. Establish soaking-up filter.

3. Establish poliklinovy a belt and adjust its tension.

4. Connect a pressure head hose to the pump and the soaking-up filter with a tank.

Prevention

Establish hoses so that they were not overwound and did not make contact with any other parts.

5. Fill in liquid.

The recommended liquid: PSF–3

6. Pump over a hydraulic drive of the amplifier of a steering.

7. Check the pressure created by the pump.