Hyundai Accent

Repair and car operation

12.3. Steering transfer without the amplifier of a steering

1–tip of steering draft;
2–collar;
3–the goffered protective cover;
4–collar;
5–lock-nut, 50–70 N • m;
6–stopper;
7–spring;
8–emphasis;
9–rubber support;
10-arm;
11-bolt,

12-gear lath;
13-steering transfer;
14-shaft of a gear wheel of steering transfer;
15-gear wheel;
16-sealing ring;
17-bearing;
18-lock ring;
19-hinge, 80–100 N • m;
20-steering draft;
21-lock-nut, 50–55 N • m;
22-nut, 16–34 N • m.

Removal

PERFORMANCE ORDER

1. Remove a forward wheel.
	2. Turn out a bolt connecting the universal hinge and a shaft of a gear wheel of steering transfer.
	3. Take шплинты and unscrew nuts of fastening of pins of spherical hinges of tips of steering bent for to rotary fists. A stripper 09568–31000 squeeze out pins of spherical hinges of tips of steering drafts from rotary fists.
	4. Remove a back support of the engine.
5. Turn out bolts and remove arms of fastening of steering transfer.
	6. Move steering transfer and get it on the right side of the car.

Dismantling

Before dismantling measure the moment necessary for a provorachivaniye of a shaft of a gear wheel of steering transfer on the average provision of a gear lath.

PERFORMANCE ORDER

1. Clear steering transfer and fix in a vice which sponges are closed by a soft material.
Prevention When fastening steering transfer in a vice wrap up steering transfer by a fabric and be careful not to damage it at compression of a vice.
2. Remove steering draft.
	3. Turn out a stopper lock-nut.
	4. The special tool 09565-21100 turn out a stopper.
	5. Remove a spring, rubber laying and an emphasis.
6. Remove a protective cover.
	7. Remove a sealing ring from a case of steering transfer.
	8. Remove a lock ring from a case of steering transfer and get a gear wheel together with the bearing.
	9. Remove from a gear wheel a lock ring of a cover of bearing knot.
	10. The special tool 09565-21000 get the bearing from a gear wheel.
11. Remove a protective cover.
	12. Using a chisel, unscrew a nut of fastening of the right steering draft.
	13. Move a gear lath completely to a case of transfer and fix a gear lath in a vice which sponges are closed by a soft material. Weaken fastening and remove steering draft from steering transfer.
14. Get a gear lath from a case of steering transfer after gear wheel removal.
	Prevention For an exception of damage of teeths of a gear lath get it on the left side.

Check

Check elements of steering transfer in the places shown in drawing.

Assembly

PERFORMANCE ORDER

1. Before assembly wash out all details in solvent.
	2. The special tool 09432-22000 press the bearing in a gear wheel.
	3. Establish a lock ring on a gear wheel.
4. Grease a gear lath, a gear wheel, the plug, the bearing and other surfaces of sliding. Recommended lubricant: SAE J310a, NLGI No. 2
Prevention Do not block lubricant the air channel in the case plug.
5. After installation of a gear lath in a case of steering transfer establish in an opening a gear wheel, having combined it with a gear lath.
	Prevention Be convinced that the gear lath is inserted into a case of steering transfer on the left side. Wipe superfluous greasing.
	6. Choose and establish the corresponding type of a lock ring to minimize люфт in the axial direction of a gear wheel.
7. Before installation of a sealing ring grease it a working edge.
	Prevention At installation it is necessary to use a new sealing ring.
8. Establish an emphasis, rubber laying and a spring.
	Prevention Grease a chashevidny part of an emphasis.
9. The special tool 09565-21000 screw a stopper. Tighten a stopper the moment of 11 N • m then tighten on a corner 30 °–60 °. Fix the provision of a stopper by a lock-nut. Moment of an inhaling of a lock-nut: 50–70 N • m
	Prevention Regulate the provision of a stopper with steering transfer in neutral situation. Put a hermetic layer between a lock-nut and a case of steering transfer.
10. Establish a tip of steering draft and a protective cover. Fix a cover new collars.
11. Measure preliminary loading with a protective cover and lubricant, turning a gear wheel the special tool 09565-11100 on one turn each 4–6 pages. Also measure starting effort of a gear lath. Full preliminary loading of a gear wheel: ±180 ° or it is less from neutral situation: 0,4–1,1 N • m ±180 ° or it is more from neutral situation: 0,3–1,6 N • m Starting effort of a gear lath: 50–300 N
Prevention Preliminary loading of a gear wheel should be measured on all length of a course of steering transfer.

Installation

PERFORMANCE ORDER

	1. Establish the rubber plug of fastening on steering transfer, as is shown in drawing.
2. Establish a gear wheel in gearing both steering transfer and gear wheel knot to a cross-section beam.
Prevention Be convinced that at installation of steering transfer and a gear wheel they are not warped or damaged. Be careful not to tighten connection by the excessive moment of an inhaling as it warps steering transfer and a gear wheel and increases effort of a steering.
3. Tighten a connecting bolt. Inhaling moment: 15–20 N • m
4. Fix steering drafts on a rotary fist. Moment of an inhaling of a nut of fastening of a pin of the spherical hinge of steering draft: 16–34 N • m
Prevention Combine a nut groove with an opening for шплинта and tighten a nut the demanded moment.
5. Adjust corners of installation of wheels.
6. Be convinced that the protective cover is not overwound and fix it a collar.