Hyundai Accent

Repair and car operation

Hyundai Accent
+ 1. Maintenance instruction
+ 2. Engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. Control, decrease in toxicity
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Transmission
+ 10. Axes and power shafts
+ 11. Suspension bracket
+ 12. Steering
+ 13. Brake system
+ 14. Body
+ 15. Central air
- 16. Electric equipment
   16.1. Specifications
   16.2. Electric chains
   16.3. Charging system
   16.4. Check of an electric chain of a charging
   16.5. Power failure check on a wire connecting the storage battery to the generator
   16.6. Check of the current developed by the generator
   16.7. Check of developed tension
   16.8. Generator
   16.9. Storage battery
   16.10. Check of specific weight of electrolit
   16.11. Charging of the storage battery
   16.12. Survey of the storage battery
   16.13. Start system
   16.14. Starter
   16.15. Check and replacement of elements of a stator
   16.16. Switch of blocking of ignition
   16.17. Check of the relay of a starter
   16.18. Check of the switch of blocking of ignition
   16.19. Radio receiver
   16.20. Loudspeakers
   16.21. Aerial
   16.22. Multipurpose switch
   16.23. Sound signal
   16.24. Safety locks
   16.25. Combination of devices
   16.26. Engine of a screen wiper of a windscreen
   16.27. Replacement of a headlight and forward index of turn
   16.28. Adjustment of light of headlights
+ 17. Appendix
+ 18. Electroschemes

16.15. Check and replacement of elements of a stator

Adjustment of a gap of a gear wheel

PERFORMANCE ORDER

1. Disconnect a wire from the plug M.
2. Additional wires connect plugs of the storage battery to plugs S and M.
3. Include ignition, thus a gear wheel of a starter it will be pushed forward.
	Prevention This check is necessary for executing during 10 with as the coil of the traction relay, otherwise, can fuse.
	4. Shchup check a gap between a gear wheel and a stopper. If the gap differs from demanded, adjust it, adding or cleaning laying between the traction relay and a forward cover. Gear wheel gap: 0,5–0,2 mm

Check of the traction relay of a starter

PERFORMANCE ORDER

1. Disconnect a wire from the plug M.
2. Additional wires connect plugs of the storage battery to plugs S and M.
3. Include ignition, thus a gear wheel of a starter it will be pushed forward. If the gear wheel is not put forward, replace the traction relay.
	Prevention This check is necessary for executing during 10 with as the coil of the traction relay, otherwise, can fuse.

Check of a holding winding of the traction relay

PERFORMANCE ORDER

1. Disconnect a wire from the plug M.
2. Additional wires connect plugs of the storage battery to the plug S and the case of the traction relay.
Prevention This check is necessary for executing during 10 with as the coil of the traction relay, otherwise, can fuse.
	3. If the gear wheel remains on a place, means, the holding winding of the traction relay is damaged and, it is necessary to replace the traction relay.

Check of return of a plunzher of the traction relay

PERFORMANCE ORDER

1. Disconnect a wire from the plug M.
2. Additional wires connect plugs of the storage battery to the plug M and the case of the traction relay.
Prevention This check is necessary for executing during 10 with as the coil of the traction relay, otherwise, can fuse.
	3. The gear wheel of a starter should be pushed forward. After a detachment of wires the starter gear wheel quickly should return to a starting position.

Operational tests (idling)

PERFORMANCE ORDER

	1. For carrying out tests of idling collect the scheme shown in drawing.
2. Establish a rheostat cursor in such situation at which the voltmeter will show tension 11,5 In, thus check a current consumed by a starter, and be convinced that the shaft of a starter is turned easily and smoothly. Current: no more than 60 And

Gear wheel with the obgonny coupling

PERFORMANCE ORDER

1. To remove the obgonny coupling from a rotor shaft, it is necessary to remove a persistent ring previously.
	2. Move a persistent ring to a gear wheel and remove a spring ring. Now the persistent ring can be removed from a shaft.

Check of a winding of a rotor

PERFORMANCE ORDER

	1. An ohmmeter check conductivity between a collector and a rotor. In the presence of conductivity replace a rotor.
	2. In the special device check a rotor winding. In the presence of short circuits replace a rotor. If the steel strip attached to a rotor, vibrates, means, in windings of a rotor there are short circuits.
	3. An ohmmeter check conductivity between collector segments. In the absence of conductivity replace a rotor.

Check of coils of a stator

PERFORMANCE ORDER

	1. An ohmmeter check conductivity of coils of a stator. In the absence of conductivity replace stator coils.
	2. With the coil established in the case, check conductivity between a conclusion of the coil and the starter case. In the presence of conductivity replace stator coils.

Check of brushes

PERFORMANCE ORDER

If the brush is worn-out to the designated limit, replace it.

Check of a shchetkoderzhatel

PERFORMANCE ORDER

Ohmmeter check conductivity between each isolated brush and a plate. In the presence of conductivity replace a shchetkoderzhatel.

Check of the obgonny coupling

PERFORMANCE ORDER

Check a condition of teeths of a gear wheel of the obgonny coupling and, in the presence of damages, replace it. Also check a condition of teeths of a gear wreath of a flywheel.

Turn a gear wheel. The gear wheel should be turned freely clockwise and be blocked at a provorachivaniye counter-clockwise

Replacement of brushes

PERFORMANCE ORDER

1. Remove a worn-out brush, thus be careful not to damage a wattled wire.

2. An emery paper smooth out the end of a wattled occasion to provide reliable contact it with a new brush.

3. Solder a wattled wire.

Replacement of the back plug

PERFORMANCE ORDER

1. Before to remove the plug, it is necessary to measure depth of its installation.
	2. The plug can be removed by means of a stripper, as is shown in drawing.
3. Establish the new plug on previously measured depth.

Starter assembly

PERFORMANCE ORDER

1. Establish the obgonny coupling for the forward end of a shaft of a rotor.
	2. Establish a persistent ring and a spring ring from the forward party of a shaft of a rotor then move a persistent ring completely to a spring ring.
	3. At lever installation in a forward cover pay attention to its situation. If the lever to establish on the contrary, the gear wheel will be put constantly forward outside and cannot work properly.