Hyundai Accent

Repair and car operation

Hyundai Accent
+ 1. Maintenance instruction
+ 2. Engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. Control, decrease in toxicity
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
- 9. Transmission
   + 9.1. Mechanical transmission
   - 9.2. Automatic transmission
      9.2.1. Specifications
      9.2.2. Control lamp of malfunctions (MIL)
      9.2.3. Diagnostic codes of malfunctions
      9.2.4. Reading of codes of malfunctions
      9.2.5. Check of pressure of transmission liquid
      9.2.6. Testing of collaboration of an automatic transmission and the engine on the motionless car (stall test)
      9.2.7. Check of level of liquid in an automatic transmission
      9.2.8. Check of operation of the lever of the selector
      9.2.9. Adjustment of the switch of indication of position of the lever of the selector
      9.2.10. Adjustment of the servo-driver of compulsory inclusion of a low gear
      9.2.11. Pressure adjustment in the highway
      9.2.12. Replacement of an oil sealing ring of a power shaft
      9.2.13. Replacement of a cable of a drive of a speedometer
      9.2.14. Removal and transmission installation
      9.2.15. Transmission repair
      9.2.16. Selector lever
      9.2.17. Adjustment of a cable of management
      9.2.18. Repair of the lever of the selector
+ 10. Axes and power shafts
+ 11. Suspension bracket
+ 12. Steering
+ 13. Brake system
+ 14. Body
+ 15. Central air
+ 16. Electric equipment
+ 17. Appendix
+ 18. Electroschemes

9.2.16. Selector lever

1–cable of management of a transmission;
2–nut;
3–solenoid of the lock of blocking;
4–wire and lamp of illumination of the control panel transmission;
5–O/D switch;
6–button;
7–handle;

8–control panel transmission;
9–adjusting cam of the lever;
10-selector lever;
11-switch of neutral provision of a transmission;
12-arm;
13-connecting tip of a cable.

Removal

PERFORMANCE ORDER

1. Remove the central console.
2. Turn out screws of fastening of the handle of the lever of the selector.
	3. Disconnect the socket of the switch of an overdrive gear, get three contacts from the socket and remove the handle from the lever.
4. Disconnect the socket of a lamp of illumination of the control panel a transmission.
	5. Remove the control panel a transmission.
	6. Remove a clip of fastening of draft.
	7. Remove a clip from the selector lever.
	8. Turn out bolts and remove washers of fastening of a cable under the dashboard.
9. Remove a clip of fastening of a cable from a transmission.
	10. Remove a cable of management of a transmission.

Check

PERFORMANCE ORDER

1. Check functioning of a cable of management by a transmission and absence of damages.

2. Check the plug on lack of wear or damages.

3. Check a spring on absence of damages and elasticity loss.

4. Check conductivity of the switch of an overdrive gear. At overdrive gear activation contacts 1 and 2 switches should be closed, and at a deaktivirovaniye contacts 1 and 3 should be closed.

Installation

PERFORMANCE ORDER

	1. Grease an internal part of the plug. Greasing: SAE J310, NLGI No. 0
	2. Move the lever of the selector and the switch of a range of a transmission to a position N and connect a management cable.
	3. At connection of a cable of management by a transmission move a cable arm while the cable will not be combined with the transmission lever.
	4. Establish a washer and screw a bolt and a nut of fastening of a cable.
	5. From the lever of the selector establish a clip.
6. Connect the socket of a lamp of illumination of the indicator of position of the lever of the selector, the O/D switch socket, the socket of the switch of a parking and the socket of a choice of a mode of movement.
	7. Establish the control panel a transmission.
	8. Put greasing in a place shown in drawing. Greasing: SAE J310, NLGI No. 2
9. Establish the selector lever in a position N, then turn an overlay of a cam so that the gap between an overlay of a cam and knot corresponded to demanded value. Gap: 15,2–15,9 mm
	Prevention Be convinced that the party In an adjusting cam of the lever settled down from the button.
10. Establish the O/D switch on the lever handle, then insert contacts into the switch socket.
11. Establish the handle of the lever and fix it two screws.
	12. Establish the central console.