Hyundai Accent

Repair and car operation


Hyundai Accent
+ 1. Maintenance instruction
+ 2. Engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. Control, decrease in toxicity
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
- 9. Transmission
   + 9.1. Mechanical transmission
   - 9.2. Automatic transmission
      9.2.1. Specifications
      9.2.2. Control lamp of malfunctions (MIL)
      9.2.3. Diagnostic codes of malfunctions
      9.2.4. Reading of codes of malfunctions
      9.2.5. Check of pressure of transmission liquid
      9.2.6. Testing of collaboration of an automatic transmission and the engine on the motionless car (stall test)
      9.2.7. Check of level of liquid in an automatic transmission
      9.2.8. Check of operation of the lever of the selector
      9.2.9. Adjustment of the switch of indication of position of the lever of the selector
      9.2.10. Adjustment of the servo-driver of compulsory inclusion of a low gear
      9.2.11. Pressure adjustment in the highway
      9.2.12. Replacement of an oil sealing ring of a power shaft
      9.2.13. Replacement of a cable of a drive of a speedometer
      9.2.14. Removal and transmission installation
      9.2.15. Transmission repair
      9.2.16. Selector lever
      9.2.17. Adjustment of a cable of management
      9.2.18. Repair of the lever of the selector
+ 10. Axes and power shafts
+ 11. Suspension bracket
+ 12. Steering
+ 13. Brake system
+ 14. Body
+ 15. Central air
+ 16. Electric equipment
+ 17. Appendix
+ 18. Electroschemes





9.2.5. Check of pressure of transmission liquid

Arrangement of sealing rings

1–oil sealing ring;
2–sealing ring;
3–sealing ring of D-shaped section;
4–sealing ring of D-shaped section; 		5–sealing ring of D-shaped section;
6–oil sealing ring;
7–sealing ring;
8–sealing ring of D-shaped section.

Check of pressure of transmission liquid is carried out to define a condition of hydraulic components and whether there are leaks.

PERFORMANCE ORDER
1. Start up the engine before transmission warming up to temperature 60~70°C.
2. Lift the forward party of the car so that driving wheels could rotate freely.
3. Connect a tachometer and arrange so that he was well visible.
4. Connect a special manometer 09452–21500 with an adapter 09452–21002 to each union of check of pressure.

For check of return pressure it is necessary to use a manometer with a limit of measurement of 3 000 kPas.
5. Measure pressure of transmission liquid at various positions of the lever of the selector and frequency of rotation of a cranked shaft of the engine. If pressure does not correspond to demanded values, check and repair transmission elements.

№ Condition Standard pressure of transmission liquid, kPa
Positions of the selector Speed of km/h Frequency of rotation of a cranked shaft Position of the lever of the selector Pressure reduction Kickdown Forward coupling Pressure of coupling Brakes of low transfers and Z.H. Pressure of a regulator of coupling Pressure of a regulator of a damper of coupling Back coupling
1 N 0 Х.Х. Neytral. 430±30 – – – – – – –
2 D 0 Х.Х. 2nd Lane. 430±30 138–277 – – – – – –
3 D (SW–ON) 110 2500 4th Lane. 430±30 840–900 – 650–710 – 570–630 – 840–900
4 D (SW–OFF) 75 2500 3rd Lane. 430±30 840–900 840–900 840–900 – 680–820 – 840–900
5 2 50 2500 2nd Lane. 430±30 840–900 – – – 490–785 – 840–900
6 L 0 2500 The 1st lane. 430±30 – – – 500–630 – 530–630 840–900
7 R 35 2500 Z.Kh. 420–480 – – – – – 500–700 –
0 1000 450 – –